A Comprehensive Guide On Lubricating Mechanical Keyboard Switches

Fans of mechanical keyboards are aware that lubricated switches improve keyboard performance. They are also aware that greasing their keys helps lower background noise. Switch faults can be prevented with proper lubrication. Your keyboard should be more responsive. This is because few manufacturers pre-lubricate their keys. There needs to be more time for you to do it yourself.

The key needs to be lubricated over time. And this procedure may be quite challenging. This is because the switches on a mechanical keyboard are many! Our instructions, however, simplify the procedure into seven steps for lubricating mechanical keyboard switches. This makes lubricating the switch simple.

Tools For Lubing Mechanical Switches

You’ll also need a clean location where you can store keyboard keys and make repairs in addition to the equipment listed below.

  • To apply grease, swap out the grease brush.
  • Switch on every key.
  • Pull the key out of the keyboard by pulling on it.
  • Take off the keyboard’s key-puller.
  • Use tweezers to grasp the switch’s tiny components.

You are equipped to select the best oil for your job.

Switch Lubes

The grease’s viscosity determines the choice of grease. The fluidity of a material is its viscosity. For instance, water has low viscosity because it moves quickly. Because jaggery drips so slowly, it is stickier. It is working on the key with oil. The primary components must maintain their position for the viscosity to be sufficient.

Depending on the type of wrench, viscosity varies.

  • When pressed, the tactile switch emits sound—nonetheless, some noise. Low viscosity is used in these switches to reduce contact loss.
  • Linear switches are noisy but do not jerk.
  • Click switches are made to be audibly loud. For locking keys, use low-viscosity oil.

Clicky switches were considered when designing. When lubricating, use caution. To prevent missing crucial clicks.

Switch Parts

Reassembling is made simpler by being aware of the key components. Once you are familiar with the purpose of each component, reassembling the switch is simple. In addition, it would be simpler to describe your situation if you need assistance.

  • The top casing holds the components together, which encloses the switch.
  • Pin joins the cross-contact with the button. Using this, the computer can identify the button that was pressed. Clicky switches differ from linear and tactile switches in part because of this.
  • Cross Contact. Most individuals ignore them. The cross-connections provide electrical impulses when the stem makes contact with the leaf, allowing the computer to record keystrokes.
  • The coil spring regulates the force needed to start the coil spring stroke. For example, the force needed to push each key. Compared to tactile switches, linear switches have looser coils.
  • Housing, all of the switch’s essential parts are housed in the bottom housing, which also transmits electrical impulses.

How To Lube Your Switches

Ensure you have the required tools and lubricants before beginning the operation. If feasible, provide enough room between keyboard keys to allow stacking rather than stacking. Additionally, you’ll need room to place the key section.

1. Remove The Key Cover.

To correctly remove the keycaps from your keyboard, use a keycap remover. Before using the keyboard, take a picture of it for reference.

2. Remove The Switches

Lift the keys from the keyboard with a key puller.

3. Disassemble The Switch

Once you get acclimated to the toggle switch, taking the keys out is simple.

  • Move the switch to the right in the Tab Alignment tool.
  • Push the upper case and pin downward. The switch ought to open as a result of the pressure.
  • Take off the lid. Again, take caution not to hurt the feet.
  • Put the lowercase, shaft, and spring in their containers.

Continue doing this until all switches are turned off.

4. Lube The Spring Coils

If you’re rotating a lot, you may utilize the batch approach rather than greasing each coil spring individually.

  • Look for a little plastic bag.
  • Add command.
  • Include 20 to 30 drops of essential oil.
  • Seal the bag’s mouth to keep the air inside.
  • Give the spring a few minutes of shaking.
  • Let the bag out.
  • Distinguish nearby coils.

5. Lube The Bottom Housing

To grease the switch, use a brush. Enter the grease with the tip. Make sure to sweep away any extra. To apply the lubricant evenly, think about using a lubricant palette.

  • Grease the machine’s lowest rail with grease.
  • Apply lubrication to the middle post’s corner.
  • Rounded off the bottom housing components’ corners.

The edges shouldn’t have any trace of white residue. Leaf lubrication is not advised.

6. Lube The Upper Housing

To distribute the lubrication uniformly across the brush, consider utilizing a lubricant palette like the housing below.

  • Lubricate the guard pin.
  • The enclosing nameplate should be lubricated.
  • Remove extra by brushing.

Some industry professionals feel that the pin should not be lubricated but rather just the area where the shaft joins the top housing.

7. Lube The Stem

  • Using a rod holder will hasten the lubrication of the rod.
  • Lightly lubricate the handle’s four sides with the oil.
  • Ensure that the grease is applied uniformly to all four sides.
  • Use a light coating on the interior of the handle.

Although lubricating the pin could lessen the tactile switch’s impact,

after lubricating each component. You may now put the new switch and keypad together. When you re-insert the key. Stay away from extra oil that might harm the contacts during reassembly.

How to Reassemble a Switch

The disassembly procedure is reversed when the switch is reinstalled.

  • Start with the scenario below.
  • Firmly press the pin into the bottom slot.
  • Verify that the cross-pin is straight.
  • Reinstall the spring.
  • It is fastened to the machine’s top.

You should be able to press the lever if the switch is correctly fitted. If not, reactivate the switch. Make sure you hold the component before repositioning the switch on the mechanical keyboard. Finally, stack the gadget on top of the button cover. You may now check your keyboard.

How To Test Your Keyboard

Install your preferred key testing program after putting the keyboard back together to check sure everything is operating as it should. You can apply too much oil if the buttons don’t work or if no touch buttons exist. Check the grease on the lever pin and contacts if the contacts are different. If the custom switch has extra grease, check it for stuck-on buttons.

If your keyboard is harsh or rough, you could have forgotten to apply oil to this location. First, the key has to be turned back on. Reapply grease after that. Make careful to stroke the spring and handle.

You have a few choices if the keyboard is unable to capture keystrokes:

  • Change the current key with a functional key. If the new switch functions, the oil switch is malfunctioning.
  • Verify that the contacts on the switch are straight. And try changing it once more.
  • Verify the lubrication of the broken connections. Then, using isopropyl alcohol to clean the leaves, try again.

The lubricating switch, however, could occasionally be broken and require replacement.

Lubing Your Mechanical Keyboard Switches

Mechanical keyboard switches may quickly be oiled with the correct equipment and pieces. Kinetic Labs provides a magnifying lens to lessen eye strain and a container to isolate the line switch from the ignition are among the items. As a result, you’ll not only receive a keyboard that performs better, but you’ll also feel accomplished.

Related Posts

Recent Stories